• English
  • $ USD
  • £ GBP
  • EUR
  • $ CAD
  • A$ AUD
  • د.إ AED

No relevant currency found

/ /

NEW IPOLLO V1 3600MH riveiw 2022

Aug 11,2022 | YESUN

1. Product introduction

Manufacturer: iPollo (the mining machine is independently developed by Zhejiang Haowei Technology)
Model: iPolloV1
Computing power: 3600M (±10%)
Power consumption: 3400W (±10%)
Video memory: 6G

2. Main components

Many people may not know much about the data above. I will take the current 8-card machine with relatively high cost performance as an example to make a comparison for you.

Graphics card: 3060ti/3070 (unlocked, after overclocking) Hash rate: 480M Power consumption 1250W-1300W

  IPOLLO V1: 3600M computing power, 3100W power consumption

In contrast, the computing power of IPOLLO V1 is about 6.45 times that of the graphics card, and the power consumption is 2 times. If calculated according to the same power consumption, the computing power of IPOLLO V1 is three times that of the graphics card! The proportion of electricity bills is extremely low, which means that the price of the shutdown currency is also extremely low!
We have also tested the prototype for a long time, and it is very stable so far.

【1】: Power adapter (The picture is for reference only, please refer to the actual product.)

【2】:Fan

【3】:V1

Interface introduction:

notes

When running the server, please place it as shown in the figure below, that is, keep it flat to avoid any damage to the server.

Sockets should be installed near the server and should be easily accessible.

The power input of this product is 200~240VAC 50/60Hz 16A. When the product is powered off, you need to turn off the power switch first.

For your safety, it is forbidden to remove any screws on the server.

Do not press the metal buttons on the case.

use and configuration

server connection

power connection

The power input of V1 is 200~240VAC 50/60Hz 16A, and the server can work normally after connecting the cables correctly.

internet relationship

(2-1) Wired connection

The interface marked "ETH" on the server panel is the network cable interface. Pay attention to the orientation when inserting the cable. Please insert the crystal head into place. A slight "click" is usually heard when inserted into place.

log in to the server

2.1 Find the server IP

Once the server is powered up and connected to the internet, start up. After the server light is on, you can find the IP of the server. You can use the "show IP" software to find the server IP as follows:


Download software: ShowIP

Double-click "Show IP" to open the software.

Briefly press the "IP Report" button on the server for 1 second, then release.

The server IP information is fed back to the PC, as shown in the following figure:

Note: The server and PC must be in the same network segment, otherwise the IP information returned by the server cannot be received.

 

2.2 Input server background management system


After finding the IP of the server, enter the obtained IP address in the browser (Google is recommended), press Enter to enter the server login interface, and enter the default administrator account and password: root

Press "Login" to enter the server background management system, as shown below:

 

Server settings

Click the "Miner Configuration" interface under "Configuration" to set the "Mining Pool" and "Network"

 

 

3.1 Fill in the mining pool information

Note: This manual uses "poolin" as an example.

ETH mining address: stratum+TCP://ETH.ss.pool in.one:443

(1) Select "Mining Pool Configuration" and fill in the mining pool information

(1-1) "Url" in "Pool 1" is filled with ETH poolin mining link address: stratum+TCP://eth . ss . pool in . one:443

(1-2) "Worker" in "Pool 1" fill in "ipllomini . 001"; "ipollomini" is a custom "sub-account" in the corresponding mining pool account; numbers suffixed with ". 001" are used for number to distinguish the server; .

Note: For customization such as numbers or letter combinations, separate them with periods, and only modify the corresponding characters without adding or subtracting spaces and punctuation.

 

Note: In order to prevent the disconnection of "Pool 1", it is recommended to set "Pool 2" and "Pool 3" at the same time to ensure that when "Pool 1" is disconnected, the system will automatically switch to "Pool 2" or "Pool 3" is running normally


3.2 Network Settings

(1) Select "Network Configuration" and fill in the network information:

 

(2) In the Protocol column, select "DHCP (dynamic)" or "Static".

(2-1) Select "DHCP (dynamic)" state: the server automatically obtains an IP address

 

After the setting is complete, click "Save and Apply", the system will be saved and automatically restarted to take effect, and the server will start to run normally.

At this point, the configuration of the server has been completed, congratulations on your becoming a qualified miner.


(2-2) Select "Static" state

Enter the IP address, netmask, gateway, and DNS server in the four boxes below, then click Save and Apply.

After page buffering is complete, the server's configuration is complete.

 

Image (static)

Note: The protocol information (static) filled in "Network Configuration" in the figure is for reference only, please refer to the on-site network protocol information for details.


3.3 Login password modification

If you need to change the server login password, the operation method is as follows:


The server is powered on and connected to the network;

Through the browser (Google), enter the server IP account password and login information in turn to enter the server web page background;

Click "System" and select "Change Password";

Enter the modified new password in "New Password", enter the modified new password again in "Confirm", and then click "Save" below to take effect:

 

Note: The "poolin" pool was used as the example above. If you use other mining pools, please modify it to the address of the mining pool you want to use, and refer to the corresponding mining pool operation instructions.

Any questions about the MINER, please feel free to contact us, we have professional technicians to solve it for you:support@yesune.com

 

Comment

Name
Email
Comment
Back to YESUN.